Supported Cards

Supported cards organized by solver.

Abaqus

*AMPLITUDE
*ASSEMBLY
*BASE MOTION
*BEAM ADDED INERTIA
*BEAM GENERAL SECTION
*BEAM SECTION
*BIAXIAL TEST DATA
*BLOCKAGE
*BOUNDARY
*BRITTLE CRACKING
*BRITTLE FAILURE
*BRITTLE SHEAR
*BUCKLE
*BULK VISCOSITY
*CECHARGE
*CECURRENT
*CFILM
*CFLUX
*CHANGE FRICTION
*CLAY HARDENING
*CLAY PLASTICITY
*CLEARANCE
*CLOAD
*COHESIVE BEHAVIOR
*COHESIVE SECTION
*COMBINED TEST DATA
*CONDUCTIVITY
*CONNECTOR BEHAVIOR
*CONNECTOR CONSTITUTIVE REFERENCE
*CONNECTOR CONTACT FORCE
*CONNECTOR DAMPING
*CONNECTOR DERIVED COMPONENTS
*CONNECTOR ELASTICITY
*CONNECTOR FAILURE
*CONNECTOR FRICTION
*CONNECTOR HARDENING
*CONNECTOR LOAD
*CONNECTOR LOCK
*CONNECTOR MOTION
*CONNECTOR PLASTICITY
*CONNECTOR POTENTIAL
*CONNECTOR SECTION
*CONNECTOR STOP
*CONSTRAINT CONTROLS
*CONTACT (General Contact)
*CONTACT CLEARANCE
*CONTACT CLEARANCE ASSIGNMENT
*CONTACT CONTROLS
*CONTACT CONTROLS ASSIGNMENT
*CONTACT DAMPING (Explicit template)
*CONTACT DAMPING (Standard templates)
*CONTACT EXCLUSIONS
*CONTACT FILE
*CONTACT FORMULATION
*CONTACT INCLUSIONS
*CONTACT INTERFERENCE
*CONTACT OUTPUT
*CONTACT PAIR
*CONTACT PRINT
*CONTACT PROPERTY ASSIGNMENT
*CONTACT PROPERTY ASSIGNMENT, PROPERTY=OFFSET FRACTION
*CONTACT PROPERTY ASSIGNMENT, PROPERTY=THICKNESS
*CONTROLS
*COUPLED TEMP-DISPLACEMENT
*COUPLING
*CREEP
*CRUSHABLE FOAM
*CRUSHABLE FOAM HARDENING
*DAMPING
*DASHPOT
*DEBOND
*DECHARGE
*DENSITY
*DEPVAR
*DFLUX
*DIAGNOSTICS
*DIELECTRIC
*DISTRIBUTING
*DISTRIBUTING COUPLING
*DISTRIBUTION
*DISTRIBUTION_ANGLE
*DISTRIBUTION_DRAPE
*DISTRIBUTION_OFFSET
*DISTRIBUTION_ORIENTATION
*DISTRIBUTION_THICKNESS
*DLOAD
*DSLOAD
*DYNAMIC
*DYNAMIC (Explicit)
*EL FILE
*EL PRINT
*ELASTIC
*ELEMENT
*ELEMENT OUTPUT
*ELEMENT PROPERTIES
*ELGEN
*ELSET
*EMBEDDED ELEMENT
*END ASSEMBLY
* END INSTANCE
*END PART
*ENERGY FILE
*ENERGY OUTPUT
*ENERGY PRINT
*EQUATION
*EULERIAN SECTION
*EXPANSION
*FABRIC
*FASTENER (SPOT WELD)
*FASTENER PROPERTY
*FILE FORMAT
*FILM
*FILTER
*FIXED MASS SCALING
*FLUID BEHAVIOR
*FLUID BULK
*FLUID DENSITY
*FLUID EXPANSION
*FLUID PROPERTY
*FRACTURE CRITERION
*FREQUENCY
*FRICTION (Explicit template)
*FRICTION (Standard templates)
*GAP
*GASKET BEHAVIOR
*GASKET CONTACT AREA
*GASKET ELASTICITY
*GASKET SECTION
*GASKET THICKNESS BEHAVIOR
*GEOSTATIC
*HEADING
*HEAT TRANSFER
*HYPERELASTIC
*HYPERFOAM
*INCREMENTATION OUTPUT
*INERTIA RELIEF
*INITIAL CONDITION (TYPE=STRESS)
*INITIAL CONDITION (TYPE=PRESSURE)
*INITIAL CONDITION (TYPE=TEMPERATURE)
*INITIAL CONDITION (TYPE=VELOCITY)
*INSTANCE
*INTEGRATED OUTPUT
*INTEGRATED OUTPUT SECTION
*ITS
*JOINT
*KINEMATIC
*KINEMATIC COUPLING
*LOAD CASE
*LOADING DATA
*LOW DENSITY FOAM
*M1
*M2
*MASS
*MATERIAL
*MEMBRANE SECTION
*MODAL_DAMPING
*MODAL DYNAMIC
*MODAL OUTPUT
*MODEL CHANGE
*MONITOR
*MPC
*MULLINS EFFECT
*NODAL THICKNESS
*NFILL
*NGEN
*NMAP
*NODE
*NODE FILE
*NODE OUTPUT
*NODE PRINT
*NONSTRUCTURAL MASS
*NSET
*ORIENTATION
*OUTPUT
*PARAMETER
*PART
*PHYSICAL CONSTANT
*PIEZOELECTRIC
*PLANAR TEST DATA
*PLASTIC
*PREPRINT
*PRE-TENSION SECTION
*PRINT
*RADIATE
*RADIATION VIEWFACTOR
*RATE DEPENDENT
*REBAR LAYER
*RELEASE
*RESPONSE SPECTRUM
*RESTART
*RESTART
*RIGID BODY
*ROTARY INERTIA
*SECTION CONTROLS
*SECTION PRINT
*SFILM
*SHEAR FAILURE
*SHEAR TEST DATA
*SHELL GENERAL SECTION
*SHELL SECTION
*SHELL TO SOLID COUPLING
*SIMPLE SHEAR TEST DATA
*SOLID SECTION
*SPECIFIC HEAT
*SPECTRUM
*SPRING
*STATIC
*STEADY STATE DYNAMICS
*STEP
*SURFACE
*SURFACE BEHAVIOR (Explicit template)
*SURFACE BEHAVIOR (Standard templates)
*SURFACE INTERACTION (Explicit template)
*SURFACE INTERACTION (Standard templates)
*SURFACE PROPERTY/*EMISSIVITY
*SURFACE PROPERTY ASSIGNMENT (Explicit template)
*SURFACE SECTION
*SURFACE SMOOTHING
*SYSTEM
*TEMPERATURE
*TIE
*TRANSFORM
*TRANSVERSE SHEAR STIFFNESS
*UNIAXIAL
*UNIAXIAL TEST DATA
*UNLOADING DATA
*USER MATERIAL
*USER OUTPUT VARIABLES
*VARIABLE MASS SCALING
*VISCO
*VISCOELASTIC
*VOLUMETRIC TEST DATA

Actran

ACCELERATION
ADMITTANCE
ANALYSIS
AXISYMMETRY
BC_MESH
BOUNDARY_CONDITION
COUPLING_SURFACE
DIMENSION
DISCRETE
DISPLACEMENT
DISTRIBUTED_LOAD
DISTRIBUTED_PRESSURE
ELEMENT
FIELD_POINT_SURFACE
FREQUENCY_DOMAIN
IMPERVIOUS
INCIDENT_SURFACE
INFINITE ADMITTANCE
INFINITE_DOMAIN
INFINITE_ELEMENT
INFINITE_FLUID
INFINITE_MESH
INTERFACE
LIGHTHILL
MATERIAL (FLUID)
MATERIAL (SHELL)
MATERIAL (SOLID)
MATERIAL (POROUS_UP)
MATERIAL (POROUS_RIGID)
MATERIAL (VISCOTHERMAL)
MESH
MEAN_FLOW
MODAL_BASIS
MODAL_EXTRACTION
MODAL_SURFACE
NODE
OUTPUT_FRF
OUTPUT_MAP
POINT_LOAD
POROUS_UP
PRESSURE
RADIATING_SURFACE
RAYLEIGH_SURFACE
RIGID_POROUS
SAVE
SHELL
SOLID
SOLVER
SOURCE
STIFFENER
SUPER_CONNECTOR
SUPER_ELEMENT
TEMPERATURE_PRESSURE
TITLE
VELOCITY
VISCOTHERMAL
VISCOTHERMAL_FLUID

ANSYS

The input translator recognizes the ANSYS cards listed below. If an unsupported field is found in a card, a message is displayed on the status bar. The messages are also printed to the file ansys.msg. General slash commands, SOLUTION commands, POST1 commands, and POST26 commands are referred to as control cards. Unrecognized cards are written to a *.hmx file.

Note: One component collector is created for every unique combination of Type, Real, Mat, and SECNUM. Surface loads on 1D elements is not supported. Property collectors are created for each real set defined in the ANSYS deck. Material collectors are also created for each material ID encountered. The component in HyperMesh is different from the component (CM) in ANSYS.