*appendmarksolverdata
Appends a mark with entities of the given type that match a defined pattern of identifying information.
Syntax
*appendmarksolverdata EntityType SolverNumber MarkID Arg1 Arg2 Arg3 Arg4…
Type
HyperMesh Tcl Modify Command
Description
Appends a mark with entities of the given type that match a defined pattern of identifying information.
Inputs
- EntityType
- The type of entities to add to the mark. See details below for different entities supported.
- SolverNumber
- A unique number for each solver that HyperMesh interfaces with:
- 70 - ACTRAN
- 2 - Abaqus
- 8 - ANSYS
- 4 - Autodv
- 10 - Deform
- 1 - Dytran
- 9 - LS-DYNA3D
- 11 - HFSolver
- 19 - HyperXtrude
- 17 - Ideas
- 1 - OptiStruct
- 22 - MADYMO3D
- 3 - Marc
- 8 - ANSYS
- 16 - Moldflow
- 1 - Nastran
- 6 - PAM-CRASH
- 18 - PAM-CRASH
- 21 - Permas
- 20 - Radioss
- markID
- The mark ID to which the entities found by this command will be appended.
- Arg1, Arg2, …
- Various arguments that vary based on entity type.
Entity Type | arg1 | arg2 | arg3 | arg4 | arg5 | arg6 |
---|---|---|---|---|---|---|
NODES | unused | attrib1 | value1 | ... | ||
ELEMS | config | type | attrib1 | value1 | ... | |
COMPS | Card Image/ Template Tag | attrib1 | value1 | ... | ||
LINES | unused | attrib1 | value1 | ... | ||
SURFS | unused | attrib1 | value1 | ... | ||
LOADS | config | type | entitytype | attrib1 | value1 | ... |
SYSTS | unused | 0-any definitioncode 1-coordinate based 2-node based (see below) |
0-any type 1-rectangular 2-cylinder 3-spherical |
attrib1 | value1 | ... |
LOADCOLS | Card Image/ Template Tag | loadstepid | attrib1 | value1 | ... | |
SYSTCOLS | Card Image/ Template Tag | attrib1 | value1 | ... | ||
SETS | Card Image/ Template Tag | entitytype 1000-justrlink nodesets 1001-omit rlink nodesets |
0-any set 1-unordered 2- ordered 3-formula |
attrib1 | value1 | ... |
PROPS | Card Image/ Template Tag | attrib1 | 3-formula value1 |
... | ||
Groups | config | type | ttag | loadstepid | attrib1 | value1 |
Groups - rwalls | config=5 | type | ttag | loadstepid | geometrytype | motiontype (see below) |
Plots | unused | attrib1 | value1 | ... | ||
Curves | unused | attrib1 | value1 | ... | ||
Blocks | Card Image/ Template Tag | attrib1 | value1 | ... | ||
Mats | Card Image/ Template Tag | attrib1 | value1 | ... | ||
Assems | unused | attrib1 | value1 | ... | ||
Titles | unused | attrib1 | value1 | ... | ||
Vectorcols | Card Image/ Template Tag | attrib1 | value1 | ... | ||
Vectors | unused | attrib1 | value1 | ... | ||
Equations | unused | config | attrib1 | value1 | ... | |
Cards | Card Image/ Template Tag | attrib1 | value1 | ... | ||
Outputblocks | unused | loadstepid | entitytype | attrib1 | value1 | ... |
Outputblocks (elems) | unused | loadstepid | 2 | class (see note) | attrib1 | value1 |
Loadsteps | unused | attrib1 | value1 | ... | ||
HM_points | unused | attrib1 | value1 | ... | ||
HM_splines | unused | attrib1 | value1 | ... | ||
Sensors | unused | attrib1 | value1 | ... | ||
Designvars | config | attrib1 | value1 | ... | ||
Beamsectcols | Card Image/ Template Tag | attrib1 | value1 | ... | ||
Beamsects | unused | attrib1 | value1 | ... | ||
Optitableentrs | unused | attrib1 | value1 | ... | ||
Optifunctions | unused | attrib1 | value1 | ... | ||
Optiresponses | unused | attrib1 | value1 | ... | ||
Dvprels | unused | attrib1 | value1 | ... | ||
Opticonstraints | unused | attrib1 | value1 | ... | ||
Desvarlinks | unused | attrib1 | value1 | ... | ||
Objectives | unused | attrib1 | value1 | ... | ||
Controlvols | Card Image/ Template Tag | attrib1 | value1 | ... | ||
Multibodies | Card Image/ Template Tag | attrib1 | value1 | ... | ||
Ellipsoids | unused | attrib1 | value1 | ... | ||
Opticontrols | unused | attrib1 | value1 | ... | ||
Optidscreens | unused | attrib1 | value1 | ... | ||
HM_tag | unused | attrib1 | value1 | ... | ||
Mbjoint | unused | attrib1 | value1 | ... | ||
Mbplane | unused | attrib1 | value1 | ... | ||
Dobjrefs | unused | attrib1 | value1 | ... | ||
Contactsurfs | Card Image/ Template Tag | attrib1 | value1 | ... | ||
Connectors | unused | attrib1 | value1 | ... | ||
Shapes | unused | attrib1 | value1 | ... | ||
Handles | unused | attrib1 | value1 | ... | ||
Domains | unused | attrib1 | value1 | ... | ||
Symmetrys | unused | attrib1 | value1 | ... | ||
Solids | unused | attrib1 | value1 | ... | ||
Morphconstraints | unused | attrib1 | value1 | ... | ||
Hypercubes | unused | attrib1 | value1 | ... | ||
Ddvals | unused | attrib1 | value1 | ... |
Examples
*createmark props 1
*appendmarksolverdata(props, 1, 1, 857, All)
Here the Property entities ("props") that use Nastran (solver "1") attribute ID 857 (from the ARG. Table) set to any value, are added to the mark.
*createmark props 1
*appendmarksolverdata(groups, 9, 1, 3, 1, 2389, 0, 97, 1, 4733, 0)
For example, you can use this command to create a mark containing all the components in the model that use the LS-DYNA *PART_INTERTIA card image.