Automesh Panel

Use the Automesh panel to generate a mesh of plate elements using surface geometry or existing shell elements to define the mesh area.

Location: Press F12 or use the search () in the top, right corner of the modeling window.
Set the options in the panel in any order that you feel comfortable using. Moving from subpanel to subpanel will not cause you to lose work. When you are finished making all your selections, click mesh to start the meshing process.
  • Set the panel mode by selecting the appropriate subpanel.
  • Select the meshing method by setting the entity selector to surfs or elems.
  • Make the required element criteria settings.
  • Set any algorithm options.
  • Select the area to be meshed using the entity selector and any extended selection methods.
    Tip: Click unmeshed and failed to make pre-defined surface selections if desired.

Size and Bias Subpanel

Use the Size and Bias subpanel to perform size and bias meshing, a flexible and powerful meshing method. A minimum of inputs are required for the element criteria settings. The algorithm options set preferences on how to handle certain situations when encountered in the geometry. When using existing finite elements as the basis for mesh generation, feature recognition settings allow the mesher to break up the areas defined by the selected elements into logical groupings with mesh controls set for each group boundary.

Size and Bias meshing works interactively or automatically. In interactive mode, manual control is presented via the Secondary Automesh panel during the mesh generation stage. Interactive meshing allows you to control mesh size and element type, and to set different mesh generation algorithms and test element quality on a surface-by-surface basis. The resulting modified mesh can be updated at any time, giving immediate feedback as to the effectiveness of the change. When meshing in the automatic mode, the mesh will be generated using only the settings, criteria and options set in the Automesh panel.

Size and biasing meshing produces a mesh with consistent element size. If meshed interactively, the number of elements (element density) node spacing (biasing), element type and mesh style can be modified for each surface face and edge.
Option Action
entity selector Select surfaces or existing finite elements to define the area to mesh.
features
When using existing finite elements as a basis for automeshing, feature recognition is used to define logical faces. Select how the automesher treats features.
connected features
Detect features based on the specified feature angle and make additional effort to void any "orphan" or non-closed feature lines.
Connected features is similar to auto detect features, but includes a more rigorous check to combine small areas and avoid creating features that end abruptly or do not connect to any other features.


Figure 1. Before Re-meshing
 


Figure 2. After Re-meshing
auto detect features
Detect features based on the specified feature angle.
feature edges
Select surface edges to preserve as features.
lines
Select lines in geometry to preserve as features.
surface edges
Detect and utilize the geometric lines associated with the selected elements as features in the re-meshing operation.


Figure 3. Before Re-meshing
 


Figure 4. After Re-meshing
interactive/automatic
interactive
Expose the interactive Automeshing secondary panel once the meshing has started.
automatic
Use only the settings and selections made in the panel to complete the meshing process.
element size Enter a floating point numeric value for the average element size. The length of any active (shared or free) surface edge will be divided by this number to determine the number of elements to place along that edge.
mesh type
Select the type of element to use during mesh creation.
Mixed
Uses quads primarily, but inserts trias when making density transitions, resulting in improved mesh quality.


Figure 5. Example: Mixed Elements
Quads
Attempts to use quads only, however, at least one tria element must be created if the sum of the element densities around the perimeter of the face or surface is odd.


Figure 6. Example: Quad Elements. The sum of element densities on the perimeter of the lower surface is odd, resulting in a tria.
Adjusting the element densities while meshing interactively can usually eliminate all tria elements.


Figure 7. Example: Quad Elements. Adjusting the bottom edge density from 11 to 10 makes the sum even and generates all-quads.
Quads only
Uses a subdividing routine that tends to generate more orthogonal quad elements.
Tria elements may still be introduced depending on the density settings.


Figure 8. Example: Quad Elements Only
Tria
Uses all trias to mesh.


Figure 9. Example: Tria Elements
R-trias
Uses right-angle triangular elements.


Figure 10. Example: R-Tria Elements
Advanced
Choose any of the other types individually for mapped elements (elements on surfaces that can be mapped to simple geometric shapes) and free elements (those that cannot easily map to simple shapes).
mapped type Select the type of elements to use for surfaces that can be mapped to simple geometric shapes.
free type Select the type of elements to use for surfaces that cannot be mapped to simple geometric shapes.
feature angle
Define a maximum angle across which elements can be maintained.
Note: Any time two adjacent elements’ normals would exceed this angle, a new set of nodes is created between them to maintain clean feature lines. Using a higher value results in elements spanning the feature line.


Figure 11. Feature Lines Preserved. With an appropriate value, the features lines are preserved.


Figure 12. Feature Lines Blurred.

If the feature angle is too high, the feature lines are blurred.

vertex angle

Define the angle used for breaking feature-edges into simpler segments.

elems to surf comp/elems to current comp Select the destination component for the newly created elements as the “current” active component or the component to which the surface belongs.
first order/second order
first order
Linear shape function
second order
Polynomial shape function
connectivity
Select how the connectivity between the newly created elements and any adjacent existing elements will be handled.
keep connectivity
Use the existing nodes on any shared boundary edges.
redo connectivity
Re-seed any existing nodes along the boundary of the newly created mesh to optimize mesh quality.
break connectivity
Ignore any existing adjacent elements and generate the mesh according to the size and type specified.
previous settings
Reuse any previous node density and spacing settings associated to the selected surface edges.
flow: align
Produce a more orthogonal quad-dominant mesh.


Figure 13. No Flow Alignment


Figure 14. Flow Alignment. Flow alignment is used, producing straighter rows of elements.
flow: size
Enforces a global mesh element size with minimal min/max element size variation.
Important: Only available when flow: align is selected.
map: size Keep the elements roughly the same size.
map: skew Prevent the mesh from producing highly-skewed elements.
anchor nodes Designate nodes that will remain and be reused in the new mesh. Anchor nodes are "fixed" so that the automesher cannot move or replace them; in essence, they are exceptions to the re-meshing operation, and the new mesh must utilize them.
link opposite edges with AR <
Link mesh settings on opposing edges of rectangular surfaces. Use the toggle to define the maximum aspect ratio (AR) to allow between large and small edge sizes of linked edges. auto corresponds to a value of 2.11. Increasing the value will add more surfaces to the linked chain, whereas decreasing the value will remove some surfaces from the linked chain.


Figure 15. Mesh without Link Opposite Edges with AR < Selected


Figure 16. Mesh with Link Opposite Edges with AR < Set to Auto


Figure 17. Mesh with Link Opposite Edges with AR < Set to 8.0

Batchmesh/QI Optimize Subpanel

Use the Batchmesh/QI Optimize subpanel to perform Quality Index meshing, an iterative automatic mesh generation method driven by element quality criteria. During the mesh generation process, the quality index of the mesh is determined by evaluating each element against a set of element quality tests. If all required element quality criteria are passed, then that element has a perfect quality index of zero. As the element quality deteriorates, the quality index value increases; a lower quality index score indicates an element more closely meets the ideal quality requirements.

The compound quality index sum of the quality index values for each of the elements is included in the current meshing area. The quality index value itself has no direct physical meaning; it is a way to compare one generated mesh pattern against another pattern generated for that same area. The quality index based mesh optimization routine attempts to modify the mesh pattern and apply node smoothing routines to obtain a lower overall quality index value.
Option Action
batchmesh/QI optimize Switch between QI optimize meshing parameters and BatchMesh parameters.
entity selector Select surfaces or existing finite elements to define the area to mesh.
features
When using existing finite elements as a basis for automeshing, feature recognition is used to define logical faces. Select how the automesher treats features.
connected features
Detect features based on the specified feature angle and make additional effort to void any "orphan" or non-closed feature lines.
Connected features is similar to auto detect features, but includes a more rigorous check to combine small areas and avoid creating features that end abruptly or do not connect to any other features.


Figure 18. Before Re-meshing
 


Figure 19. After Re-meshing
auto detect features
Detect features based on the specified feature angle.
feature edges
Select surface edges to preserve as features.
lines
Select lines in geometry to preserve as features.
surface edges
Detect and utilize the geometric lines associated with the selected elements as features in the re-meshing operation.


Figure 20. Before Re-meshing
 


Figure 21. After Re-meshing
element size Enter a floating point numeric value for the average element size. The length of any active (shared or free) surface edge will be divided by this number to determine the number of elements to place along that edge.
mesh type
Select the type of element to use during mesh creation.
Mixed
Uses quads primarily, but inserts trias when making density transitions, resulting in improved mesh quality.


Figure 22. Example: Mixed Elements
Quads
Attempts to use quads only, however, at least one tria element must be created if the sum of the element densities around the perimeter of the face or surface is odd.


Figure 23. Example: Quad Elements. The sum of element densities on the perimeter of the lower surface is odd, resulting in a tria.
Adjusting the element densities while meshing interactively can usually eliminate all tria elements.


Figure 24. Example: Quad Elements. Adjusting the bottom edge density from 11 to 10 makes the sum even and generates all-quads.
Quads only
Uses a subdividing routine that tends to generate more orthogonal quad elements.
Tria elements may still be introduced depending on the density settings.


Figure 25. Example: Quad Elements Only
Tria
Uses all trias to mesh.


Figure 26. Example: Tria Elements
R-trias
Uses right-angle triangular elements.


Figure 27. Example: R-Tria Elements
Advanced
Choose any of the other types individually for mapped elements (elements on surfaces that can be mapped to simple geometric shapes) and free elements (those that cannot easily map to simple shapes).
use current criteria/criteria file Switch between using the current element quality criteria or use a custom criteria file.
edit criteria Open the Criteria File Editor.
Important: Only available when user current criteria is selected.
feature angle
Define a maximum angle across which elements can be maintained.
Note: Any time two adjacent elements’ normals would exceed this angle, a new set of nodes is created between them to maintain clean feature lines. Using a higher value results in elements spanning the feature line.


Figure 28. Feature Lines Preserved. With an appropriate value, the features lines are preserved.


Figure 29. Feature Lines Blurred.

If the feature angle is too high, the feature lines are blurred.

vertex angle

Define the angle used for breaking feature-edges into simpler segments.

smooth across common edges with Node smoothing moves nodes across adjacent surface edges whose feature angle is less than the value specified. When selected, strict adherence to the geometry of the surface edges in not enforced for non-feature edges; some deviation from the geometry can occur.
elems to surf comp/elems to current comp Select the destination component for the newly created elements as the “current” active component or the component to which the surface belongs.
first order/second order
first order
Linear shape function
second order
Polynomial shape function
connectivity
Select how the connectivity between the newly created elements and any adjacent existing elements will be handled.
keep connectivity
Use the existing nodes on any shared boundary edges.
redo connectivity
Re-seed any existing nodes along the boundary of the newly created mesh to optimize mesh quality.
break connectivity
Ignore any existing adjacent elements and generate the mesh according to the size and type specified.
previous settings
Reuse any previous node density and spacing settings associated to the selected surface edges.
flow: align
Produce a more orthogonal quad-dominant mesh.


Figure 30. No Flow Alignment


Figure 31. Flow Alignment. Flow alignment is used, producing straighter rows of elements.
flow: size
Enforces a global mesh element size with minimal min/max element size variation.
Important: Only available when flow: align is selected.
anchor nodes Designate nodes that will remain and be reused in the new mesh. Anchor nodes are "fixed" so that the automesher cannot move or replace them; in essence, they are exceptions to the re-meshing operation, and the new mesh must utilize them.
preserve edges Open the Preserve Edges tool and define settings to ensure that specific component edges and feature lines do not accidentally get discarded during auto cleanup or batch meshing.

Edge Deviation Subpanel

Use the Edge Deviation subpanel to set specific meshing parameters to limit how far the mesh elements can deviate from the actual edges of the surfaces meshed, or when in the case of re-meshing elements, deviation from inferred edges based on features.

Controls for the minimum and maximum allowable element size, edge deviation and maximum angle are introduced with this method. Edge deviation normally occurs on curved edges, because individual elements have straight edges and therefore can only approximate a curve.


Figure 32. Meshing Curved Surfaces. The planar elements (tan color) can deviate from the curved grey geometry.
Edge deviation applies to both surface geometry and when re-meshing elements. Automeshing using the edge deviation subpanel automatically selects the best element size to approximate a curve, within the limits that you specify. The max deviation and max angle settings are the primary controls for this effect.
Note: Edge deviation meshing differs from size and bias meshing, which only meshes with elements of a uniform size that you specify.
This method can produce a mesh in which the element size varies, even within the same surface. Areas of high curvature will tend to have smaller elements than areas of low or no curvature. The element size boundaries controls this effect.


Figure 33. Example: Edge Deviation. Edge deviation control when meshing creates smaller elements, and spaces nodes closer together to limit how much the elements can deviate from the surface edges.
Option Action
entity selector Select surfaces or existing finite elements to define the area to mesh.
features
When using existing finite elements as a basis for automeshing, feature recognition is used to define logical faces. Select how the automesher treats features.
connected features
Detect features based on the specified feature angle and make additional effort to void any "orphan" or non-closed feature lines.
Connected features is similar to auto detect features, but includes a more rigorous check to combine small areas and avoid creating features that end abruptly or do not connect to any other features.


Figure 34. Before Re-meshing
 


Figure 35. After Re-meshing
auto detect features
Detect features based on the specified feature angle.
feature edges
Select surface edges to preserve as features.
lines
Select lines in geometry to preserve as features.
surface edges
Detect and utilize the geometric lines associated with the selected elements as features in the re-meshing operation.


Figure 36. Before Re-meshing
 


Figure 37. After Re-meshing
interactive/automatic
interactive
Expose the interactive Automeshing secondary panel once the meshing has started.
automatic
Use only the settings and selections made in the panel to complete the meshing process.
min/max element size
Define element size boundaries.
Note: The values specified here are rigidly enforced, even if other settings (that is max deviation) are violated.
max deviation Define an allowable deviation between the element edge and the surface edge. To meet this requirement, element edge lengths along a curved surface edge are reduced as needed down to a lower limit set by the min elem size field.
max angle Define the maximum allowable angle between two element edges.

This helps determine the size of an element to create; if the angle formed by adjacent element edges would exceed this value, smaller elements are tried until the angle is equal to or less than this value.

mesh type
Select the type of element to use during mesh creation.
Mixed
Uses quads primarily, but inserts trias when making density transitions, resulting in improved mesh quality.


Figure 38. Example: Mixed Elements
Quads
Attempts to use quads only, however, at least one tria element must be created if the sum of the element densities around the perimeter of the face or surface is odd.


Figure 39. Example: Quad Elements. The sum of element densities on the perimeter of the lower surface is odd, resulting in a tria.
Adjusting the element densities while meshing interactively can usually eliminate all tria elements.


Figure 40. Example: Quad Elements. Adjusting the bottom edge density from 11 to 10 makes the sum even and generates all-quads.
Quads only
Uses a subdividing routine that tends to generate more orthogonal quad elements.
Tria elements may still be introduced depending on the density settings.


Figure 41. Example: Quad Elements Only
Tria
Uses all trias to mesh.


Figure 42. Example: Tria Elements
R-trias
Uses right-angle triangular elements.


Figure 43. Example: R-Tria Elements
Advanced
Choose any of the other types individually for mapped elements (elements on surfaces that can be mapped to simple geometric shapes) and free elements (those that cannot easily map to simple shapes).
mapped type Select the type of elements to use for surfaces that can be mapped to simple geometric shapes.
free type Select the type of elements to use for surfaces that cannot be mapped to simple geometric shapes.
feature angle
Define a maximum angle across which elements can be maintained.
Note: Any time two adjacent elements’ normals would exceed this angle, a new set of nodes is created between them to maintain clean feature lines. Using a higher value results in elements spanning the feature line.


Figure 44. Feature Lines Preserved. With an appropriate value, the features lines are preserved.


Figure 45. Feature Lines Blurred.

If the feature angle is too high, the feature lines are blurred.

vertex angle

Define the angle used for breaking feature-edges into simpler segments.

elems to surf comp/elems to current comp Select the destination component for the newly created elements as the “current” active component or the component to which the surface belongs.
first order/second order
first order
Linear shape function
second order
Polynomial shape function
connectivity
Select how the connectivity between the newly created elements and any adjacent existing elements will be handled.
keep connectivity
Use the existing nodes on any shared boundary edges.
redo connectivity
Re-seed any existing nodes along the boundary of the newly created mesh to optimize mesh quality.
break connectivity
Ignore any existing adjacent elements and generate the mesh according to the size and type specified.
previous settings
Reuse any previous node density and spacing settings associated to the selected surface edges.
flow: align
Produce a more orthogonal quad-dominant mesh.


Figure 46. No Flow Alignment


Figure 47. Flow Alignment. Flow alignment is used, producing straighter rows of elements.
flow: size
Enforces a global mesh element size with minimal min/max element size variation.
Important: Only available when flow: align is selected.
map: size Keep the elements roughly the same size.
map: skew Prevent the mesh from producing highly-skewed elements.
link opposite edges with AR <
Link mesh settings on opposing edges of rectangular surfaces. Use the toggle to define the maximum aspect ratio (AR) to allow between large and small edge sizes of linked edges. auto corresponds to a value of 2.11. Increasing the value will add more surfaces to the linked chain, whereas decreasing the value will remove some surfaces from the linked chain.


Figure 48. Mesh without Link Opposite Edges with AR < Selected


Figure 49. Mesh with Link Opposite Edges with AR < Set to Auto


Figure 50. Mesh with Link Opposite Edges with AR < Set to 8.0
anchor nodes Designate nodes that will remain and be reused in the new mesh. Anchor nodes are "fixed" so that the automesher cannot move or replace them; in essence, they are exceptions to the re-meshing operation, and the new mesh must utilize them.

Surface Deviation Subpanel

Use the Surface Deviation subpanel to mesh within limits of element deviation from a surface.
Important: Only accessible when meshing surfaces.
The meshing behavior in this subpanel is driven by distances between flat elements and model geometry. When flat elements are used to approximate a curved surface, there is always a discrepancy between each element and the actual curve of the surface, because the element uses a straight line between two nodes.


Figure 51. Surface Deviation. A gap is visible between the curved edge of the surface and the element edges.
The Surface Deviation meshing chooses the mesh density based on the severity of this deviation. Where the threshold deviation would be exceeded, smaller elements are used to reduce the deviation.


Figure 52. Surface Deviation Meshing. Smaller elements are used to accurately represent curved surfaces. Larger elements are used where the geometry shows less curvature.

Surface Deviation meshing only works in an automatic mode; interactive meshing with the Secondary Automesh panel is not possible. However, use the refine function to set a specific desired mesh size for a point, line or surface face. This option accesses another temporary subpanel that is slaved to the Surface Deviation subpanel. From this subpanel, select fixed points, lines, or surfaces to define an area in which you desire a more refined mesh. You can specify a different element size for these areas, which displays as a color-coded numeric value: yellow for points, green for lines, or red for surfaces. An option to show all or show active toggles the view of these numeric values; show active displays only the refinement value for the most recently selected point, line or surface, while show all shows all values for all selected entities.

After specifying refinement options, click mesh to create a smoothly-scaled mesh from your base element size to the size specified in the refine options.


Figure 53. Surface Deviation, Refinement Not Applied. The colored numbers indicate refinement targets: point (yellow), line (green), and surface (red).


Figure 54. Surface Deviation, Refinement Applied. The mesh is finer near the point (yellow), along the line/edge (green), and on the surface (red).
Option Action
entity selector Select surfaces or existing finite elements to define the area to mesh.
element size Enter a floating point numeric value for the average element size. The length of any active (shared or free) surface edge will be divided by this number to determine the number of elements to place along that edge.
growth rate Determine how rapidly elements can increase in size as they are created further and further away from features.


Figure 55. Example: Growth Rate. Elements further from the features grow larger with each row.
min element size Elements with edges smaller than this value will not be created.
span angle Controls the element size at curve input. The smaller the angle, the more refined curvature will be and the more preserved the input shape will be. By default span angle is 25.0 degrees.
Important: Valid only for element-based surface deviation.


Figure 56. Example: Span Angle. β is the span angle of the edge ab. The length of ab is less than 2R( sin β/2 ).
feature angle
Define a maximum angle across which elements can be maintained.
Note: Any time two adjacent elements’ normals would exceed this angle, a new set of nodes is created between them to maintain clean feature lines. Using a higher value results in elements spanning the feature line.


Figure 57. Feature Lines Preserved. With an appropriate value, the features lines are preserved.


Figure 58. Feature Lines Blurred.

If the feature angle is too high, the feature lines are blurred.

max deviation Define an allowable deviation between the element edge and the surface edge. To meet this requirement, element edge lengths along a curved surface edge are reduced as needed down to a lower limit set by the min elem size field.
mesh type
Select the type of element to use during mesh creation.
Mixed
Uses quads primarily, but inserts trias when making density transitions, resulting in improved mesh quality.


Figure 59. Example: Mixed Elements
Quads
Attempts to use quads only, however, at least one tria element must be created if the sum of the element densities around the perimeter of the face or surface is odd.


Figure 60. Example: Quad Elements. The sum of element densities on the perimeter of the lower surface is odd, resulting in a tria.
Adjusting the element densities while meshing interactively can usually eliminate all tria elements.


Figure 61. Example: Quad Elements. Adjusting the bottom edge density from 11 to 10 makes the sum even and generates all-quads.
Quads only
Uses a subdividing routine that tends to generate more orthogonal quad elements.
Tria elements may still be introduced depending on the density settings.


Figure 62. Example: Quad Elements Only
Tria
Uses all trias to mesh.


Figure 63. Example: Tria Elements
R-trias
Uses right-angle triangular elements.


Figure 64. Example: R-Tria Elements
Advanced
Choose any of the other types individually for mapped elements (elements on surfaces that can be mapped to simple geometric shapes) and free elements (those that cannot easily map to simple shapes).
mapped type Select the type of elements to use for surfaces that can be mapped to simple geometric shapes.
free type Select the type of elements to use for surfaces that cannot be mapped to simple geometric shapes.
elems to surf comp/elems to current comp Select the destination component for the newly created elements as the “current” active component or the component to which the surface belongs.
first order/second order
first order
Linear shape function
second order
Polynomial shape function
connectivity
Select how the connectivity between the newly created elements and any adjacent existing elements will be handled.
keep connectivity
Use the existing nodes on any shared boundary edges.
redo connectivity
Re-seed any existing nodes along the boundary of the newly created mesh to optimize mesh quality.
break connectivity
Ignore any existing adjacent elements and generate the mesh according to the size and type specified.
previous settings
Reuse any previous node density and spacing settings associated to the selected surface edges.
closed volume proximity Dynamically create finer mesh across the narrow spaces between features in a closed volume/solid entity.
free edge deviation Produce a finer mesh around curved edges (such as holes) even on planar surfaces.

Clear this checkbox to base the mesh on surface chordal deviation only.

refine Open a temporary subpanel, from which you can perform mesh refinement on or around specific points, lines, or surfaces.

Use the switch to select the type of entity to use as a basis, then select the points/lines/surfaces and specify an element size in the numeric box.

show refined If you use refine to perform localized mesh refinement, this checkbox displays the refinement element size you assigned to each entity marked for refinement.

Rigid Body Mesh Subpanel

Use the Rigid Body Mesh subpanel to create a quick mesh to represent the topology of a rigid object.
Important: Only the automatic meshing mode is available.

Rigid bodies are surfaces that are expected to be treated as undeformable in the solution. One example of a rigid body is in metal-forming. When modeling the results of a die pressing down on a metal sheet, it's important to model the shape of the die because that determines the shape of the metal sheet after being pressed. However, during a forming analysis the stresses and deformations of the die itself are not of interest, only those of the formed metal sheet. Other applications for rigid bodies include the impactors used in vehicle crash simulation.

A mesh that accurately represents the rigid geometry is important for such simulations to allow the solver collision detection routines to work effectively and accurately. Since stress and deformation of the rigid body are not calculated by the solver, the rigid body mesh focuses on accurately modeling the shape of the body rather than on producing a high-quality mesh. To this end, it uses the same faceting and shading routines that are used for drawing the model graphics. The resulting mesh may have high aspect ratio or extremely tapered elements that would not be suitable for solution, but can accurately represent the geometry.

Figure 65 and Figure 65 illustrate the differences between surface deviation meshing and rigid body meshing. Both meshes were generated using the same parameters in terms of min/max element size, maximum deviation and feature angle, and mesh type.


Figure 65. Cone with Surface Deviation Based Mesh. Many small elements are required to capture the geometry, even so, the elements exhibit a lot of warpage and those at the tip are distorted and do not accurately represent the geometry.


Figure 66. Cone with Rigid Body Mesh. The shape of the object can be accurately modeled using fewer larger elements since the element shape is not a concern.
Option Action
entity selector Select surfaces or existing finite elements to define the area to mesh.
min/max element size
Define element size boundaries.
Note: The values specified here are rigidly enforced, even if other settings (that is max deviation) are violated.
max deviation Define an allowable deviation between the element edge and the surface edge. To meet this requirement, element edge lengths along a curved surface edge are reduced as needed down to a lower limit set by the min elem size field.
max feature angle Define a maximum allowable break angle between adjacent elements. The element size is adjusted such that the angle between the normals of adjacent elements does not exceed this value.


Figure 67. . The minimum and maximum element sizes are 3 and 50 respectively. The mesh is constrained by the max deviation value set to 0.5. The element size is set such that the maximum distance between the element and the spherical surface does not exceed this setting.


Figure 68. . The minimum and maximum element sizes are 3 and 50 respectively. The deviation setting is relaxed to 3.0, and the mesh is bound by the maximum feature angle setting of 45 degrees.
mesh type Select the type of element to use during mesh creation.
Mixed
Uses quads primarily, but inserts trias when making density transitions, resulting in improved mesh quality.


Figure 69. Example: Mixed Elements
Tria
Uses all trias to mesh.


Figure 70. Example: Tria Elements