hmabaqus

Translates a binary or ASCII Abaqus results file into a HyperMesh binary results file.

Syntax

hmabaqus [options] <inputfile> <outputfile> <modelfile>

Application

Translators

Inputs

One or more of the following options can be used. Use the command hmabaqus-u to obtain these options.
-d
Displacements
-rot
Rotations
-v
Velocities
-a
Accelerations
-nflux
NFLUX
-nflxrot
NFLUX rotations
-von
von Mises
-tr
Tresca
-hydropr
Hydrostatic Pressure
-tsi
Third Stress Invariant
-pstrs
Principal Stresses
-shstrs
Shear Stresses
-sed
Strain Energy Density
-temp
Temperature
-sinktemp
Sink Temperature
-filmcoef
Film Coefficient
-ecursmag
ECURS magnitude
-ncursmag
NCURS magnitude
-recurmag
RECUR magnitude
-ecdmag
ECD magnitude
-ecd1
ECD1
-ecd2
ECD2
-ecd3
ECD3
-resflux
Residual Flux
-conflux
Concentrated Flux
-intflux
Internal Flux
-fluxs
FLUXS
-nodetemp
Nodal Temperatures
-ts
Total Strains
-ls
Logarithmic Strains
-ns
Nominal Strains
-ps
Plastic Strains
-pstrn
Principal Strains
-pnomsn
Principal Nominal Strains
-plogsn
Principal Logarithmic Strains
-stress
Stresses
-rmsstrs
RMS Stresses
-rmsstrn
RMS Strains
-rf
Reaction Forces
-rm
Reaction Moments
-pl
Point Loads
-thick
Shell Thickness
-sinv
Maximums (default off)
-s1
First Surface (default off)
-s2
Second Surface (default off)
-cr
Contact Results
-epot
Electrical Potential
-por
Pore or Acoustic Pressure (default off)
-ps1v
Principal Stress 1 (Vector)
-ps2v
Principal Stress 2 (Vector)
-ps3v
Principal Stress 3 (Vector)
-sh1v
Shear Stress 1 (Vector)
-sh2v
Shear Stress 2 (Vector)
-sv1
State Variable 1 (default off)
-sv2
State Variable 2 (default off)
-svn
State Variable n (default off)
-sv20
State Variable 20 (default off)
-notrans
Do not convert local displacements into global (default off)
-pc56
Read results for v5.6 on PC (default off)
-maxsim
Max simulations (default 999) (default off)
-step
For specific STEP results (default off)
-inc
For specific ITERATION results (default off)
-disk
Translation is performed on disk
-size
Number of entities (10000 default) -file Scratch file name
-h3d
Outputs file to an H3D file instead of to an hmresults file. The file includes model and results information that was translated. The model must contain geometry for it to be output to an H3D file. -noip (default off) turns off all processing of element integration point values. If you ask Abaqus to average values to element centroids, this option makes a considerable difference in the amount of memory needed. If you also specify a result type that is found on element integration points, and the translator comes across such a result during processing, it reports an error (default off).
-sv1, -sv2,..., -sv20
State variables were being treated differently for some element groups from others. For some element types, they were always included, and, for others, they were processed only if specifically listed, with the default listing all of them. Now, all are uniform. They are translated only if you requests them to be translated. Also, the translator used to allocate memory to process all 20 allowable state variables whether you asked for any or not. Now, you can turn them on individually, and use just the minimum memory necessary, or you can turn on the first N of them using -nsdv (default off).
-nsdv <number>
Turns on the first <number> state variables (max of 20). If you list both individual state variables and also the -nsdv option, the listed ones are the only ones processed. You can get complete compatibility with older versions by using "-nsdv 20". (default off).
In addition, the following parameters are also available when the results translation is not performed on the analysis machine and when the results file is binary. One of these parameters may need to be specified to indicate where the analysis result file was created.
-cray
Cray
-dec
Dec 5000
-decalpha
Dec Alpha
-hp
Hewlett Packard
-pc
PC
-sgi
SGI
-sun
Sun

Example

N/A